![how to make a photo booth backdrop stand how to make a photo booth backdrop stand](https://file.weddingchicks.com/672045_fiftyflowers137.jpg)
The background can be rolled down from the pipe and rolled back up again once the shooting is done.įor now I’ve only done black and white rolls, but new ones are easy to make and install. I’ve fixed the end of the pipes with two hose clamps. To mount the fabric to the pipe do a small side cut to the pipe, where the end of the fabric will be inserted. (if you are using schedule 40 pipes, this is probably not relevant, it is just a weird thing on European pipes).Ĭut the thick end at 50mm x 150mm pipe (the one holding the fabric) so it can rotate around the thinner 40mm pipe. Now at the last of the 150cm pipes, the thick end need to be cut off to make it fit between the two angles which hold the horizontal pipes. Try these the most popular 22 extremely innovative DIY Photo Booth Backdrop Ideas at home today. then add the long 200cm and 20cm vertical pipes. Why to spend money on photo studio to get photo background. (Easy storage = Storing them at any corner of the house, if you are willing to pay the rant from the significant other)įirst, start with the stand: Use 4 of the 90 degrees angles, the two branches and the two 30cm long pipes to build the “legs” of the stand.Ĭonnect the two 150cm pipes to create a rectangle as the bottom part of the stand. While someone lines up the frame with the hole, the other person can start to screw the frame to the plywood. Now flip the plywood over again and place your frames over the holes. Pull the fabric tight and staple them onto the back. A fabric in the color of your choice, opaque, 150cm x 400cm (around 3 € per meter) The BuildĪfter you’re done, all the PVC pieces can be separated again portability and easy storage. Using a razor cut the fabric from inside the frame holes at an angle like the picture.All the PVC pieces together were less than 20 €.
![how to make a photo booth backdrop stand how to make a photo booth backdrop stand](https://ae01.alicdn.com/kf/H896c05e20f464a768784c997524aad2bf/Backdrop-Stand-Frame-Arch-Photo-Booth-Pipe-Drape-Wedding-Ceremony-Photography-Diy-Adjustable-Metal-Kit-Weighted.jpg)
Additionally, for each background color I bought a 50mm x 150cm pipe to mount the background fabric on.PVC Pipes, I used 40mm diameter pipes because they are the cheapest at the hardware store next to me, while still providing enough support.
#How to make a photo booth backdrop stand full#
I decided to make my own full body background system with changeable colors for less money. I’ve read about quite a few photographers using a 35€ IKEA window shade as a “seamless” half body background. I used screws to attach the 2x4s to the wood stakes in the ground.It has been a long time since we had a good solid studio PVC build (pun intended), so I was quite thrilled when David Schöppe sent in this full body backdrop stand made from PVC I attached the 2×4’s to the wall with a couple of Joist Hangers and put two small wood stakes in the ground where the 2x4s met the ground. The two additional supports made it stronger and gave me peace-of-mind. Enough wind or someone pushing on the walls could bend the T-Posts and make the walls fall. We set the walls up the night before and I wanted some extra protection against wind. The wall did not need these, but I figured I would put them there just in case. Just in case I needed them, I brought a few extra 2x4s to attach to the walls mid way and run down at an angle to the ground. You can build a frame from a variety of materials, but a wooden frame is the most practical option. The best way to avoid the wrinkled, messy look of a draped backdrop is to wrap your backdrop around a frame before mounting it on the wall. I used lag bolts because I wanted something strong. Method 2: Build a frame for your backdrop and mount it to the wall. I used 5/16″ x 2″ lag bolts to attach the T-Posts to the back of the walls.
![how to make a photo booth backdrop stand how to make a photo booth backdrop stand](https://www.simplebooth.com/img/diy_start.png)
You can see the green T-Posts running down the 2x4s. Here are the fence boards from Lowes that I used, hopefully this link always stays up: Ģx4s are 2x4s, do you really need a link? You can see the difference in the middle section of the wall which is slightly shorter than the outside two. I ended up needing a few other boards and was closer to HomeDepot and noticed that Lowe’s lumber was higher quality and the boards I went with were 6″ wide where HomeDepot’s are 5.5″ wide. I went to Lowe’s to purchase lumber because I happened to be closer to Lowe’s at the time. That would have made the cost of my wall reach $500. I saw the prefab shiplap boards, but they were $18-$25 each. I saw prebuilt fence style walls for $120 and I would have needed three of them. The photo backdrop wall received a lot of comments, so I thought I would do a tutorial on how I built it.Īs I mentioned before, I wanted to do this on the cheap.
#How to make a photo booth backdrop stand free#
If you are planning a photo booth for a wedding or a party, we have FREE photo prop printables to make your photo props in our DIY New Year’s Eve Photo Booth Props post. A post shared by Four Friends Market on at 10:24am PDT (Generally speaking, for a photo booth set up, you will probably want to shoot between f/4 and f/5.6.) Photobooth Props.